6KW Sauna Steamer Generator with Controller Sauna Room Bathing Equipment Accessories 220‑240V Condition: Item Type: Steam Generator Material: Stainless Steel Voltage: 220-240V Temperature Control: 35-55℃ (95-131℉) Controller Control Distance: 50m / 164ft Product Size: Approx. 39.5 x 39.5 x 14.5 cm / 15.6 x 15.6 x 5.7 in Weight: Approx. 10000g / 352.7oz Installation of the Steam Generator: 1. The steam generator can be installed on the wall or on the ground, but it must be firm. Install the steam generator as close as possible to the bathtub or bathroom. To fix the machine on a vertical wall, firstly loosen the two screws on the cover and remove the outer cover. There are holes in the cover at the upper left and right for fixing the machine on the wall. Close the cover after fixing. In order to provide good maintenance services, the sign must be placed where it can be seen, and the machine must be installed in a convenient place for maintenance. 2. It is strictly forbidden to install the machine in outdoor, humid, high temperature or places that may be freezed or corroded. At the same time, it is strictly prohibited to place it near flammable and explosive places such as paint, diluting agent and gasoline. It should be placed in a dry and ventilated place.3. The steam generator can only be installed horizontally. Attention in the Steam Bath: 1. The elderly, pregnant women or those with heart disease, hypertension, diabetes or other adverse health reasons cannot use this equipment temporarily. Except under the guidance of a physician. 2. Do not smoke, exercise or drink alcoholic beverages in the steam bath. 3. If you feel unwell, nauseous or sleepy, please exit the steam room immediately. 4. Take care of your children at all times during the steam bath. 5. It is necessary to install an exhaust fan outside the steam room to allow air circulation. Warning: 1. If the machine is installed in a place where it is difficult for the user to access, the water supply valve must be installed in an easily accessible place in an emergency. 2. The pressure of the solenoid valve is 2Kg/cm². If the water pressure is too high, in order to avoid damage to the solenoid valve, you can properly close the small water inlet valve or install an inlet water pressure reducing valve. 3. Do not use a saddle or needle valve on the inlet pipe. The hoses should be dredged and flushed before the final connecting to pipe. 4. It is strictly prohibited to install a blocking valve in the steam pipe. Do not block or bend the U channel. Otherwise, condensed water will be generated to hinder the circulation of steam. The steam pipe should have a certain inclination when the pipe is arranged horizontally, so that the condensed water returns to the steam generator or flows to the steam nozzle. 5. The steam generator must not be installed outdoors to prevent icing in the machine. And it must be installed in a place where it is easy to maintain. The machine should be installed horizontally with the arrow pointing up, otherwise it cannot be turned on. 6. Copper pipe material must be used for pipe installation. Plastic, acrylic, aluminum-plastic pipe or other similar materials are strictly prohibited as steam pipes. Because the temperature allowed by these materials can not get 150℃ and higher. 7. Steam pipe inlets, all other inlets and gaps should be sealed to prevent steam from escaping and damaging the machine and other objects. 8. Draining water from the water tank into the steam room may cause burns and damage to the building materials used in the steam room. Before use, please check according to the following terms: 1. The machine is properly grounded. The diameter of the grounding wire must be greater than 4mm². 2. Whether the machine model is selected properly. If it is not selected properly, the matching steam room may not get the preset temperature. 3. The voltage connected to the steam generator is well selected (ie 220V). If a 220V steam generator is connected to a 380V voltage, the electric heating tube and the circuit board will be damaged.  4. The steam generator must be installed vertically and horizontally. 5. Select the correct cable and circuit interrupter.